Free Jewelry Projects

Fireblossom Earrings Tutorial

Determine desired loop lengths and cut leather. For these earring, I cut 2 pieces at about 5" and 2 pieces at about 3".

Read More

Emma Dog Tag Tutorial

Emma is in our warehouse daily, and I wanted to honor her with some Jewelry. New to stamping? See Metal Stamping 101. The 3mm Bridgette stamp set allowed a long phone number and a name to fit perfectly.

Read More

I love My Dog Bracelet Tutorial

Pre-stretch cord by pulling firmly from both ends a few times. Attach small binder clip or bead stopper 2-3” from one end of stretch cord.

Read More

Sour Patch Bracelet Tutorial

Set the crystals in the bezel settings, and press prongs down smoothly over the stones using the nylon jaw pliers. Link settings together with jump rings. Add clasp to one end, using a jump ring. Add desired length of chain to other end.

Read More

Springtime Serenade Bracelet Tutorial

Place one 10mm crystal into one bezel setting and use needle nose pliers to gently bend prongs over crystal. Repeat for all five colors.

Read More

Summer Rain Bracelet Tutorial

Place a wire guard on the round link and crimp a 10-inch piece of flex wire through the wire guard (see Jewelry Basics 101 - PDF).

Read More

Sweet and Sour Engraved Bracelet Tutorial

Edged cuff bracelets also work great for leather, fabric, beaded designs and more!

Read More

Take Flight Bracelet Tutorial

Use a small amount of E-6000 adhesive to glue one cord end onto the cording. Using a head pin, slide on one spacer bead, an apatite pebble bead and one more spacer bead. Make a wrapped loop. Make 4 sets.

Read More

The Imp Bracelet Tutorial

Plan out design, and stamp words and symbols. ("I Drink and I Know Things" is a quote from Game of Thrones, and the colors used here are the colors of house Lannister.)

Read More

Thin Blue Line Friendship Bracelet Tutorial

Create a loop large enough for the button to go through. A clipboard works well to anchor knotting projects. Clamp the loop under the clip.

Read More

TierraCast Bee Bracelet Tutorial

Cut 20" of 1.5mm cord in your choice of color and cut again into 2 pieces, one 12" and one 8". Feed one open end of each cord through each end of honeycomb link (as shown in picture), secure with knot by wrapping working end around cord and forming overhand knot, aiming tail away from loop. Secure with glue after final tightening.

Read More

TierraCast Monstera Bracelet Tutorial

Pre-stretch cord. Attach center of cord to button shank with Larks-Head knot then tie overhand knot.

Read More

TierraCast Monstera Trio Bracelet Tutorial

Cut cord into 3 12" pieces. String one button onto each cord, then string 3 hole bars and barrel beads. Position as desired, then lightly crimp barrel beads in place. Trim cords to desired length (allow 1.5" for clasp and jump rings) then secure crimp ends with glue or crimping.

Read More

Tough Girl Rhinestone Chain and Leather Bracelet Tutorial

Measure your rhinestone chain pieces to the same length for best results. Use an awl to pierce holes in the leather, and sew the chain to the cuff. Seal thread ends with GS Hypo Cement.

Read More

Tranquil Spangle Bracelet Tutorial

Determine desired bracelet length; add one inch. Cut a piece of cord 4 times this length. (7" bracelet + 1" = 8". 8" x 4 = 32").

Read More

Trio of Pearls - Leather Bracelet Tutorial

Add a pearl to one end of the cord, and tie a simple overhand knot on each side of the pearl. Use an awl to help pull the knots tight up against the pearl bead. This will be the "button" portion of your button/loop clasp.

Read More

Triple the Fun Bracelet Tutorial

Using alcohol wipes, clean both Palace Crimp Ends on the inside. Using the black suede lace, make a double overhand knot in the center. Pull down on the knot to make sure it is snug.

Read More

Tri-Tone Cuff Bracelet Tutorial

Using a pre-cut and finished bracelet blank, and precut 6" patterned wire makes this bracelet assemble in a snap!

Read More

Wrapped in Rhinestone Lashed Bracelet Tutorial

For a step-by-step tutorial with images, see the Easy to Make Lashed Rhinestone and Leather Bracelet blog post.

Read More

Goodnight Moon Pins Tutorial

Cut loops off the moon charms and file smooth. For one pin, antique the brass components and bar pin with Win-Ox™ before assembling.

Read More
See More Ideas