Posts Tagged ‘shrine’

Create a Hinged Metal Memory Journal

Thursday, July 18th, 2013

Use a hinge to turn shrine-shaped metal blanks into a journal!

Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things. This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Hinged Book Necklace made with shrine-shaped metal blanks

Decide on the layout, location of the hinge and other decorative elements. Using a checkered hammer, apply texture to the top and bottom panels of the journal. Patina, file rough edges and clean.
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Layout

Cut the hinges, which can be as wide or as narrow as you choose. For 3/32 tubing, make hinges that are one-half inch deep. You need an odd number of hinge tabs. Measure, mark and saw tabs into the top panel. Use plenty of cut lube to prevent the saw blade from sticking when cornering.
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Create Hinge Tabs

Using wide, flat nose pliers, crease and fold each tabs up to a 90 degree angle. The position of the fold determines whether the hinge will be visible from the front of the pendant, or only from the back side. Keep the textured sides face up, so the design is consistent.
Carefully roll tabs into cylinders using chain nose pliers or medium bail making pliers. Leave hinges a bit loose until after you have inserted the tubing, then you can tighten for best fit.
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Roll Into Cylinders

Use a tube cutting jig to cut a length of tube 1mm longer than the width of your piece (for 1/2mm on each side).
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Cut Tubing

Slide tubing down the channel and finesse hinges as needed. Rivet tubing into place to finish the hinge. Open and close hinge to ensure a proper fit.

This free DIY jewelry design by Sondra Barrington features antique brass, nickel silver, metal etching, dapping and creating hinges.

Assemble Hinge and Insert Tubing

Working with the bottom panel, lay out etched metal pieces for the cover and inside page. Cut, file and patina as necessary. Leave sufficient room for the hinge to lay flat against the bottom panel.
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Lay out Etched Metal Page

Measure, mark and punch holes for decorative rivets, accents and center piece (using the small side of the hole punch).
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Prepare Embellishments

Using two-part epoxy, carefully glue the etched metal panels into place.
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things. This free DIY jewelry project features metal etching, metal stamping, dapping and riveting. Antique brass, nickel silver, copper and natural agate were used in creating this design. The one-step looping plier was used for the handmade chain.

Lay out Etched Metal Page

Using a dapping set, dome two small round shapes that can nest one inside the other. Patina, file away any rough edges and clean the domed metal. Layer, and rivet domed metal nests onto the top panel. Connect top and bottom panel with rivets. Use a tube rivet at the top so that you can thread a jump ring through it (if you choose).
Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Rivet Domes Into Place

Carefully clean and polish the pendant before attaching the necklace chain.

Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Clean Finished Pendant

Handmade jewelry looks great on a custom beaded necklace, on leather cording, silk ribbon or chain. I created a necklace by making individual links using the one-step looping plier, eye pins, metal beads and natural agates. The links were connected using jump rings.

Hinged Pendant Memory Journal created by Sondra Barrington of Rings & Things.  This free DIY jewelry project features metal etching, metal stamping, dapping and riveting.  Antique brass, nickel silver, copper and natural agate were used in creating this design.  The one-step looping plier was used for the handmade chain.

Memory Journal Necklace

This free DIY Memory Journal pendant was created by designer Sondra Barrington of Rings & Things. This necklace features riveting, metal etching, antique brass shrine stamping blanks, dapping, and metal stamping. The chain was created in an ombre pattern using natural agate gemstone beads, TierraCast antique brass bead caps, metal heishi trade beads and the one-step looping plier with antique copper head pins.

Create a Healing Shrine

Thursday, June 6th, 2013

Making handmade jewelry for someone is a unique and inspiring way to show you care.  This “Healing Shrine” was created for a friend suffering from cancer.  It was inspired by our new brass blank shapes and a recent trip to Santa Fe, NM.

An antique brass "Healing Shrine" created for a friend suffering from cancer. The glass vial is filled with 'holy dirt' from a sacred site purported to have healing powers.

Healing Shrine

Each year, thousands of people pilgrimage to El Santuario de Chimayo seeking blessings.  Many visitors take a small amount of “holy dirt” from the site, in hopes of a miraculous cure for themselves or someone who could not make the trip.  I chose to encase my “holy dirt” in a glass portal, that I nested inside a brass reliquary.  Following are instructions for how-to create this DIY jewelry design using stacked brass layers and cold connections.

First, envision your shrine and decide how you want it to look and feel.  Decide on contents for your glass bottle.  Unscrew the top loop from the cork in the glass vial.  Measure, mark and punch holes for rivets (using the small side of the hole punch).

Stamp word “heal” on the metal band designed to hold the glass vial.  Measure the band to ensure that it is going to fit.

Measure metal band to fit glass vial

Measure and bend metal band to fit glass vial

Using bail making pliers, bend the center of the band into a curved shape, leaving each end flat.  Cut to shorten as needed.  File the ends.

Arrange pieces and punch metal

Arrange pieces and punch metal

Rivet the stamped metal band into place after double-checking that it will snugly hold the glass once it is assembled.

Punch holes and rivet band to hold bottle

Rivet the band into place (to hold the vial)

Insert tube rivets in holes between the front and back of shrine, stacking copper heishi trade beads between the layers (to fill the space and strengthen the connection between the top and bottom layers).

Use metal heishi beads as spacers between the layers of metal.

Heishi beads as spacers between layers

  Rivet them into place.  Note: Be careful, it is very difficult to reinstall the heishi spacer beads if they fall off the tubes!

Place all metal heishis before riveting back panel into place

Place all  heishi beads before riveting together

Patina and clean.  Using two-part epoxy, attach a magnet to the back side of the shrine.  Carefully fill vial with contents.

Fill the bottle and install it into reliquary

Fill the vial and pop it into place

Once the glue has cured, pop the glass vial inside the band.  This DIY jewelry project can be a pendant, magnet or pin.